Hazard Factor Identification And Efforts To Control Work Accidents In Welding Activities In Tanks (Confined Space) At PT. Menubar Kaltim

Authors

  • istiarto University Of Widya Gama Mahakam
  • Wesi Fatmawati University Of Widya Gama Mahakam

DOI:

https://doi.org/10.24903/kujkm.v9i2.2676

Keywords:

Workload, Work Stress, Work Fatigue, Occupational Health and Safety

Abstract

Background: Hazard factors and risks on ships, especially in welding activities in tanks (confined space) there are hazard and risk factors that cannot be avoided by workers. Metode yang digunakan dalam penelitian ini adalah metode kualitatif dengan pendekatan fenomenologi melalui teknik wawancara, observasi, dan dokumentasi terhadap 6 informan, 3 informan utama dan 2 informan pendukung 1 informan kunci. From the results of research through interviews, it can be known that hazard factors, especially in welding activities in the tank (confined space) there are 17 potential hazards with 19 levels of risk and the impact of each category level including 0 risks being included in the low category, 6 risks of being included in the moderate category, 7 risks being included in the high category, 6 other risks are. There are still workers who do not comply with the importance of work safety, some workers actually know that the hazard factors around them are very risky but workers still carry out unsafe behaviour, forget to use personal protective equipment, do not check first, incomplete equipment and damaged equipment as well as worker awareness in equipment maintenance and maintenance of workplace areas.

Objectives : This research aims analayze hazard factor and work accident control efforts in tanks welding activities (confined space) at PT. Menubar Kaltim

Research Metodes: The type of research used is qualitative which is a research method carried out with the main aim of giving an objective picture of a situation (Notoatmodjo, 2012). The research design used in this study is by phenomenological approach method. The approach is a study that describes phenomena that occur and can be observed. This study is for (data presentation) and conclucion (verification).

Findings: Based on the results of interviews conducted by researchers with main informants, supporting informants, key informants, about hazard factors and efforts to control work accidents in welding activities in tanks (confined space) at PT. MK. The main informants in this study were 3 welding workers in the tank (confined space), 1 safetyman and 1 person in charge of the machine in a limited space as a supporting informant who also conducted supervision in the work area (hot work, confined space) and 1 person as a key informant, namely the supervisor. The main information in this study is that each informant has different knowledge due to the experience of workers while working as regulated according to Law Number 11 concerning Job Creation in 2020 and Undung-Law Number 1 of 1970 concerning work safety.

Conclusion: Welding activities in tanks (confined space) have a very high level of work accident risk for welding workers in ship tanks. Welding activities in tanks (confined space) at PT. Menubar Kaltim has all levels of risk categories, namely low, moderate, high to extremely high. The results obtained from data analysis using JSA and RA to determine the results on welding activities in tanks (confined space) 17 potential hazards with 19 risk levels of risk and 0 risk levels of low, 6 moderate, 7 high, 6 extremely high.

Downloads

Download data is not yet available.

References

A. Ferina, H. B. (2021). Analisis Risiko Keselamatan Dan Kesehatan Kerja (K3) Dengan Metode Hazard Identification, Risk Assessment, and Risk Control (Hirarc) Pada Proses Pengelasan (Welding) Di Pt Industri Kapal Indonesia (Persero) Makassar. Skripsi Sarjana, DEPARTEMEN KESELAMATAN DAN KESEHATAN KERJA FAKULTAS KESEHATAN MASYARAKAT UNIVERSITAS HASANUDDIN, Makassar.

Ardian, A. (2010). Perawatan dan Perbaikan Mesin. Kementrian Pendidikan Nasional Universitas Yogyakarta Teknik Mesin, December, 1–77.

Bakhtiar, D. ., & Sulaksmono, M. (2013). Risk Assessment Pada Pekerjaan Welding Confined Space Di Bagian Ship Building Pt Dok Dan Perkapalan Surabaya. The Indonesian Journal of Occupational Safety and Health, 2(1), 52–60.

Hidayat, M. C., Nuruddin, M., Studi, P., Industri, T., Teknik, F., Gresik, U. M., & Gkb, J. S. (2021). E -ISSN : 2746-0835 Volume 2 No 4 ( 2021 ) JUSTI ( Jurnal Sistem Dan Teknik Industri ) ANALISIS IDENTIFIKASI BAHAYA KECELAKAAN KERJA MENGGUNAKAN JOB SAFETY ANALYSIS ( JSA ) DENGAN PENDEKATAN HAZARD IDENTIFICATION ,RISK ASSESSMENT AND RISK CONTROL ( HIRAR. 2(4), 557–571.

Jasasila. (2017). 225486-Peningkatan-Mutu-Pemeliharaan-Mesin-Peng-5Dfcc0E7. 17(3), 96–102.

Lestari, F. A., Kusuma, A. N., & Pertiwi, W. E. (2018). Implementasi Hot Work Permit System sebagai Upaya Pencegahan Kecelakaan Kerja. Faletehan Health Journal, 5(1), 10–18. https://doi.org/10.33746/fhj.v5i1.3

Menu Prosedur Keamanan, Keselamatan dan Kesehatan Kerja Tami / October 22, 2020 / News. (2020).

Ngah, H., Hairon, S. M., Hamzah, N. A., Noordin, S., & Shafei, M. N. (2022). Assessment of Knowledge, Attitude, and Practice on Safe Working in Confined Space among Male Water Services Workers in the Central Region of Malaysia. International Journal of Environmental Research and Public Health, 19(12). https://doi.org/10.3390/ijerph19127416

Patel. (2012). Penelitian Kualitatif : Metode Penelitian Kualitatif. In Jurnal EQUILIBRIUM (Ke 3, Vol. 5, Issue

January). Alfabeta.

Perbawa, A. P. (2018). Identifikasi Bahaya pada Hot Working di Confined Space dengan HIRARC dan FTA. Proceeding 2nd Conference On Safety Engineering Program Studi D4 Teknik Keselamatan Dan Kesehatan Kerja – PPNS, 2581, 647–652.

Setyoko. (2017). Sistem Manajemen Keselamatan dan Kesehatan Kerja (SMK3) Pada Perusahaan. Orbith, 13(3), 172–177.

Smith, & Sonesh. (1988). Pengertian Keselamatan Dan Kesehatan Kerja. Digilib.Unhas.Ac.Id.

Suryawan, K. S. B., Pio, R. J., & Rumawas, W. (2018). Pengaruh Keselamatan dan Kesehatan Kerja Terhadap Kepuasan Kerja Pada PT. Pandawa Surya Sentosa Di Kota Balikpapan, Kalimantan Timus. Jurnal Administrasi Publik, 4(61), 1–8.

Terhadap, K., Kerja, P., Kasus, S., Pt, P., & Karya, G. (2021). Jurnal Ekonomi. 3(2), 176–184.

Sabila, D. A., Perencanaan, S. S., Pemeliharaan, M., Pendahuluan, I., & Power, I. (2019).

STRATEGI MANAJEMEN PEMELIHARAAN UNTUK MENGOPTIMALKAN. Jurnal Bisnis STRATEGI, 28(2), 110–122.

Peraturan Menteri Tenaga Kerja Dan Transmigrasi Republik Republik Indonesia, Pub. l. No. Nomor Per.08/Men/Vii/2010, 1 (2010).

Lima, M. (2013). Keselamatan dan Kesehatan Kerja Keselamatan dan Kesehatan Sarana untuk Produktivitas (I). International Labour Organization.

Cirebon, K. (2020, May). Kesehatan dan Keselamatan Kerja itu Penting. ARTIKEL DJKN, 1–8.

Heryawan, H., dkk. (2018). Analisis Penyebab Ketidakpatuhan APD pada pekerja Manual handling PT X Tahun 2018. [jurnal] Universitas Esa Unggul 2Dosen, 11.

Napitupulu, D. S., Pane, J. P., Sinaga, A., Simorangkir, L., & Boris, J. (2022). Peningkatan pengetahuan tentang keselamatan dan kesehatan kerja di gema kasih galang. [jurnal] Jurnal Pengabdian Masyarakat Berkemajuan, 6, 1046–1052.

Kastruri. (n.d.). Metode mengatasi kerusakan pada peralatan instrumentasi di industri migas. [jurnal] Forum Teknologi, 07(1), 53–63.

Pengganti Undang-Undang Republik Indonesia Nomor 2tahvn 2022, Pub. l. No. Nomor 2 tahvn 2022, 1117 (2022).

Maisyaroh, S. (2010). Implementasi Job Safety Analysis Sebagai Upaya Pencegahan Kecelakaan Kerja Di Pt. Tri Polyta Indonesia, Tbk. [skripsi] Universitas Sebelas Maret Surakarta.

Undang-Undang Republik Indonesia Nomor 1 tahun 1970 tentang keselamatan kerja, 1 (1970).

Smith, and Sonesh (1988). Pengertian Keselamatan Dan Kesehatan Kerja Digilib.Unhas.Ac.Id.

Suryawan, Kadek Senli Bonix, Riane J. Pio, and Wehelmina Rumawas. 2018. “Pengaruh Keselamatan Dan Kesehatan Kerja Terhadap Kepuasan Kerja Pada PT. Pandawa Surya Sentosa Di Kota Balikpapan, Kalimantan Timus.” Jurnal Administrasi Publik 4 (61): 1–8.

Hidayat, Muhammad Choirul, Moch Nuruddin, Program Studi, Teknik Industri, Fakultas Teknik, Universitas Muhammadiyah Gresik, and Jl Sumatera Gkb. 2021. “E -ISSN : 2746-0835 Volume 2 No 4 ( 2021 ) JUSTI ( Jurnal Sistem Dan Teknik Industri ) ANALISIS IDENTIFIKASI BAHAYA KECELAKAAN KERJA MENGGUNAKAN JOB SAFETY ANALYSIS ( JSA ) DENGAN PENDEKATAN HAZARD IDENTIFICATION , RISK ASSESSMENT AND RISK CONTROL ( HIRAR” 2 (4): 557–71.

Bakhtiar, D.S, and M Sulaksmono. 2013. “RISK ASSESSMENT PADA PEKERJAAN WELDING CONFINED SPACE DI BAGIAN SHIP BUILDING PT DOK DAN PERKAPALAN SURABAYA.” The Indonesian Journal of Occupational Safety and Health 2 (1): 52–60

Lestari, Fitri Ayu, Andiko Nugraha Kusuma, and Wiwik Eko Pertiwi. 2018. “Implementasi Hot Work Permit System Sebagai Upaya Pencegahan Kecelakaan Kerja.” Faletehan Health Journal 5 (1). Universitas Faletehan: 10–18. doi:10.33746/fhj.v5i1.3.

Terhadap, Karyawan, Performa Kerja, Studi Kasus, Pada Pt, and Garuda Karya. 2021. “JURNAL EKONOMI” 3 (2): 176–84.

Smith, and Sonesh (1988). Pengertian Keselamatan Dan Kesehatan Kerja. Digilib.Unhas.Ac.Id.

Jasasila. 2017. “225486-Peningkatan-Mutu-Pemeliharaan-Mesin-Peng-5Dfcc0E7” 17 (3): 96–102.

Prasetyaningrum, Dyan Ratna. 2011. “Penerapan Sistem Izin Kerja Sebagai Upaya Pencegahan Kecelakaan Kerja Di PT APAC INTI CORPORA SEMARANG.” FK UNS.

Presiden RI. Undang-Undang Republik Indonesia Nomor 1 Tahun 1970 Tentang Keselamatan Kerja. Presiden Republik Indonesia 1–20 (1970).

Rofiq, M.A., and Azhar, A. (2022). Hazards Identification and Risk Assessment In Welding Confined Space Ship Reparation PT. X With Job Safety Analysis Method. BERKALA SAINSTEK 10, 175.

Julianto, Eko, Bambang Sri Waluyo, and Ayu Indah Pratiwi. 2019. “BAGI MASYARAKAT INDUSTRI

GALANGAN KAPAL ( Studi Pada PT . JANATA MARINA INDAH Unit II SEMARANG )” 01 (02): 73–78.

NIOSH. 1987. “A Guide for Safety in Confined Spaces.” DHHS (NIOSH) PUBLICATION NO. 87-113.

Dhanistha, Wimala L, and M Roshi. 2023. “Risk Analysis of Hot Working in Confined Space Using Confined Space Risk Analysis ( CRSA ) and Bowtie Analysis Method on LPG Tanker Repair Process” 2 (February): 28–34.

Ngah, Hamiza, Suhaily Mohd Hairon, Nurul Ainun Hamzah, Shahronizam Noordin, and Mohd Nazri Shafei. 2022. “Assessment of Knowledge, Attitude, and Practice on Safe Working in Confined Space among Male Water Services Workers in the Central Region of Malaysia.” International Journal of Environmental Research and Public Health 19 (12). MDPI. doi:10.3390/ijerph19127416.

Arifin, Kadir, Mohd Akhir Ahmad, Azlan Abas, and Mohamad Xazaquan Mansor Ali. 2023. “Systematic Literature Review: Characteristics of Confined Space Hazards in the Construction Sector.” Results in Engineering. Elsevier B.V. doi:10.1016/j.rineng.2023.101188.

Wahana, D. (2018). Analisis Risiko Keselamatan Dan Kesehatan Kerja Welding Confined Space Bagian Erection Pt. Pal Indonesia (Persero) Surabaya. In Digital Repository Universitas Jember.

Downloads

Published

2023-12-29

How to Cite

istiarto, & Wesi Fatmawati. (2023). Hazard Factor Identification And Efforts To Control Work Accidents In Welding Activities In Tanks (Confined Space) At PT. Menubar Kaltim. KESMAS UWIGAMA: Jurnal Kesehatan Masyarakat, 9(2). https://doi.org/10.24903/kujkm.v9i2.2676

Issue

Vol. 9 No. 2 (2023): December

Section

Articles

License

Copyright (c) 2023 istiarto istiarto, Wesi Fatmawati

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution 4.0 International License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.